1964-74 Mopar Starter Mounting Hardware Set
Starter mounting hardware set for all 1964-74 Mopar models, excluding Hemi with Manual transmission. Each set includes studs, washers and all other hardware needed to mount the starter. Will not fit direct drive starter....
Painless Remote Starter Solenoid Set
This set allows you to position the starter solenoid any place you need to in order to make maintenance easier, clean up an inner fender or just replace a factory starting circuit. Installation Instructions: Download Here Set...
In today's high-heat environment, starters take in a lot of damaging heat that destroys the windings of the starter and solenoid. To combat this problem, we offer a non-conductive strap-on heat shield with a highly-reflective...
3/8"-16 X 3-5/8" Starter Mount Bolt
This replacement shouldered medium length bolt commonly used to secure starters with a cast iron staggered pattern nose to a big block engine. Two bolts required per vehicle.
GM Starter Bolt 3/8"-16 X 1-7/8"
Genuine GM starter bolt for various models. Replaces OE # 14097279 - starter mounting bolt (short) 3/8-16 x 1.87" (or 3/8"-16 X 1-7/8"). Fits most (non gear reduction) small block & big block chevy starters. Sold...
1964-77 Pontiac; Starter Solenoid Heat Shield
Reproduction of the original starter solenoid heat shield designed for use with various 1964-77 Pontiac models. This solenoid heat shield is manufactured in a two-piece riveted waffle design providing superior thermal...
1957-84 Ford; Motorcraft; Starter Solenoid Relay Switch
Motorcraft replacement starter solenoid relay switch for various 1957-84 Ford and Mercury models including Mustang, Cougar, Falcon, and F-Series Truck. Depending on the year, make, and model, this is a service replacement may...
Starter Bolt 3/8"-16 X 4-11/16"
Replacement starter bolt for models that require a 3/8"-16 x 4-11/16" bolt.
Painless Hot Shot Starter Solution; without Engine Bump Start Switch
The solution for vehicles with GM starters that are hard to start when hot, or vehicles with old or worn out electrical systems. Works by boosting available amperage to the starter solenoid. Installation Instructions:...
Painless Hot Shot Starter Solution; without Engine Bump Start Switch
Classic $36.99 ea
Painless Hot Shot Plus Starter Solution; with Engine Bump Start Switch
The solution for vehicles with GM starters that are hard to start when hot, or vehicles with old or worn out electrical systems. Works by boosting available amperage to the starter solenoid. The Hot-Shot Plus model includes...
Painless Hot Shot Plus Starter Solution; with Engine Bump Start Switch
Classic $56.99 ea
Starter Bolt; 3/8"-16 X 4.33"; For 4.3L 5.0L 5.7L, or 502 Engine
Genuine GM starter bolts for various models. For 4.3L 5.0L 5.7L, or 502 Engine. Replaces GM Numbers 12338064, 09000852, or 10465167. Works with GM Performance 9000852 or 12606096 high-torque mini starters, also works with...
1950-62 Ford/Mercury; Bendix Starter Drive Assembly; Inertia Type
Replacement bendix drive assembly for Ford 12V Inertia Starter Motors. Replaces Ford part# C1AZ-11350-A or Motorcraft Part# SD-3.
1957-77 Ford / Mercury; Starter Solenoid Relay Switch; Service Replacement; 12v
Replacement starter solenoid relay switch for various 1957-77 Ford and Mercury models including Mustang, Cougar, Falcon, and F-Series Truck. Depending on the year, make, and model, this is a service replacement may differ in...
1957-77 Ford / Mercury; Starter Solenoid Relay Switch; Service Replacement; 12v
Classic $11.99 ea
Touch Sensitive Starter System with Advanced Security - For Use without Ron Francis Harness
Looking for something to set your ride apart, make it more like late model rides? Install this complete touch sensitive starter system from Ron Francis. This system simulates all five positions of a typical keyed ignition...
1955-59 Chevrolet Starter Support Bracket
Over the years this always comes up missing. Give your starter the support it needs with this bracket.
Touch Sensitive Starter System with Advanced Security - For Use with Ron Francis Harness
Looking for something to set your ride apart, make it more like late model rides? Install this complete touch sensitive starter system from Ron Francis. This system simulates all five positions of a typical keyed ignition...
1970-84 Chevrolet, GMC; Starter Motor Brace; For 168 Tooth Starter
Stamped steel starter motor brace for a wide variety of 1970-84 Chevrolet and GMC car and truck models with 168 tooth starter. Over a period of years, the starter motor brace can be lost or discarded when the starter is...
1962-70 Chevrolet; Starter Mount Bolt Set; Small Block
Reproduction of the original style starter bolts designed for use with 1962-70 Chevrolet models with small block engines. This bolt set contains one 3/8"-16 x 1-27/32" short bolt, and one 3/8"-16 x 4-21/64" long bolt. This is...
1958-81 Long Version Starter Solenoid
The starter motor solenoid commonly needs to be replaced due to heavy use and heat which is generated from the engine and exhaust manifolds.
1947-55 Chevrolet, GMC Truck; Floor Mounted Starter Switch
Reproduction of the original floor mounted starter switch designed for use with 1947-55 Chevy and GMC truck models. Each switch is designed and manufactured to replicate the original in fitment and functionality. Note: 1955...
1947-59 Chevrolet, GMC Truck; Foot Starter Return Spring
Reproduction of the original foot starter return spring for use with 1947-1959 Chevrolet and GMC truck models. Each spring is manufactured in quality stamped steel to factory specifications. Springs are manufactured in the...
1955-56 Chevrolet Starter Solenoid
Replacement starter solenoids for 1955-56 Chevrolet models. For original V8 starters with external lever-type starters. Measurements: 3 1/2" long 2 5/8" diameter
1966-69 Mopar Starter Mounting Hardware Set
Starter mounting hardware set for all 1966-69 Mopar models with a Hemi engine and manual transmission. This mounting set is for the direct drive starter that was used exclusively on 1966-69 manual Hemi models. Each set...
1964-81 GM; Starter Shim Set; 5 Pieces
5-piece starter shim set for Chevrolet and Pontiac models. Set includes (1) 1/16" shim, (2) 1/32" shims and (2) 1/64" shims. They are used to shim the starter to the engine block.
1951-56 Ford / Mercury; Replacement Starter Relay Solenoid Switch; 6-Volt
Replacement style starter relay solenoid switch for 1951-56 Ford and Mercury cars and trucks. Replaces Ford part# B5A-11450.
1951-56 Ford / Mercury; Replacement Starter Relay Solenoid Switch; 6-Volt
Classic $15.99 ea
1955-81 GM; Starter Motor Brush Set
When rebuilding your original starter motor, it is usually necessary to replace the brushes. The brushes are the most commonly worn out part of the starter which can cause failure. These brushes are stamped 945 and contain a...
1955-93 Long Version Gold Series Starter Solenoid
The solenoids are manufactured with a high-temperature insulated wire for better heat resistance, a nickel-plated mounting bracket for better ground and an increased contact area on studs for higher electrical current...
1968-74 Chevrolet; Starter Motor Solenoid Heat Shield; with Big Block; Various Models
Reproduction of the factory-style solenoid heat shield designed for use on various 1968-74 big block Chevrolet models. This high-quality shield is manufactured in stamped steel to match the original configuration for an...
1968-74 Chevrolet; Starter Motor Solenoid Heat Shield; with Big Block; Various Models
Classic $24.99 ea
1968-74 Mopar Starter Dust Shield
Replacement starter dust shield for 1968-74 Mopar models. Mounts between starter and bellhousing.
1968-74 Chevrolet; Starter Heat Shield Slotted Retainer Nut; Big Block
Reproduction of the starter heat shield retainer nut designed for use with a variety of 1968-74 Chevrolet big block models as listed. This special retaining nut holds part number # 361443 starter motor solenoid heat shield in...
1968-74 Chevrolet; Starter Heat Shield Slotted Retainer Nut; Big Block
Classic $13.99 ea
1966-72 Chevrolet; Starter Mount Bolt Set; Big Block
Reproduction of the original style starter bolts designed for use with 1966-72 Chevrolet models with 396, 401, 409, 427, 454 big block engines. This bolt set contains two 3/8"-16 x 3-5/8" bolts. Starters with a cast iron...
1966-81 Small Block 168 Tooth Starter Motor Brace
Over a period of years, the starter motor braces are usually lost or discarded when the starter is replaced. Without this brace, undue strain will occur to the starter motor body causing wear or damage. When this happens you...
1967-74 Dodge, Plymouth; Mounting Bolt Set; 4-Piece Set; For Plastic Starter Shields
Starter shield mounting bolt set for plastic starter shields. Each set includes (4) 1/4"-20 x 3/4" Serrated head bolts to mount PLASTIC K Frame and Starter Splash Shields on all 1966-74 auto trans models equipped with the...
1967-74 Dodge, Plymouth; Mounting Bolt Set; 4-Piece Set; For Plastic Starter Shields
Classic $8.99 ea
1982-92 Short Version Gold Series Starter Solenoid (Metric)
The starter motor solenoid commonly needs to be replaced due to heavy use and heat which is generated from the engine and exhaust manifolds. Fits 1982-90 models. The gold series solenoids are manufactured with a...
1982-98 Short Version Starter Solenoid (Metric)
The starter motor solenoid commonly needs to be replaced due to heavy use and heat which is generated from the engine and exhaust manifolds. Applications to fit various models.
1967-72 Dodge, Plymouth A-Body; Starter / Transmission Linkage Splash Shield
Starter/transmission linkage splash shield for A-Body vehicles. Comes with 9 staples and a drill bit for installation. Original factory assembly line manual shows 9 staples to be used but we have seen anywhere from 5 to 7...
1967-72 Dodge, Plymouth A-Body; Starter / Transmission Linkage Splash Shield
Classic $11.99 ea
Starter Motor Field Coil: Original field coil required when rebuilding your original starter motor. This unit contains four coils.
1947-59 Chevy, GMC Truck; Foot Starter Pedal Pad
Reproduction of the original style starter pedal pad designed for use with 1947-59 Chevrolet and GMC trucks. The foot starter pedal pad can crack and wear out over time. Replacing the pad will help the appearance of the...
If you want to put a TH350 or TH400 transmission in your 1955-56 Chevrolet V8 265 and would like to continue using the stock starter, then this is just what you'll need. Requires 168 tooth flex plate. 1957's will require...
1955-56 Chevy Bel Air; 265 V8; Engine Block to Transmission Starter Alignment Spacer Plate; TH350, TH400
Classic $211.99 ea
1947-55 Chevrolet, GMC; Foot Starter Bellow Boot
This reproduction of the original foot starter bellow boot designed for use with 1947-55 Chevrolet and GMC truck models. Each bellow boot is manufactured in quality EPDM rubber to factory specifications matching the original...
1955-59 Chevrolet, GMC Truck; Starter Wire Firewall Grommet
Reproduction of the original starter wire firewall grommet for use with 1955-59 Chevrolet and GMC truck models. Each grommet is manufactured from EPDM rubber compound to correct factory dimensions. Will replace the old or won...
1937-Early 55 Chevrolet/GMC Truck; Starter Foot Knob; Cast Iron; SST Shaft
Foot knob and rod attach to the starter switch. The cast iron top is included with the long stainless steel shaft. This shaft is only used with the 1947-55 Chevy and GMC but the screw on top fits 1937-55. These mushroom...
1937-Early 55 Chevrolet/GMC Truck; Starter Foot Knob; Cast Iron; SST Shaft
Classic $14.99 ea
1955-62 Chevrolet, GMC Truck; Floor Mounted Starter Switch
Reproduction of the original floor mounted starter switch designed for use with 1955-1962 Chevy and GMC truck models. Each switch is designed and manufactured to replicate the original in fitment and functionality. Note: 1955...
1969-70 GM Starter Solenoid Mounting Set; Big Block; Heat Sheild
Reproduction of the starter heat shield retainer nut designed for use with a variety of Chevrolet big block models. This special retaining nut holds part number # 361443 starter motor solenoid heat shield in place on models...
Starter Motor Solenoid Heat Shield
This heat shield is used for all standard (non-metric) solenoids on V8 model cars and trucks. Features easy mounting and is produced in stainless steel.
1966-74 Camaro, Impala, Nova; Starter Solenoid Wire Harness Retainer Clip
Reproduction of the commonly discarded starter solenoid wire harness retainer clip for use with various 1967-74 GM models as listed. This reproduction retainer is manufactured to correct factory specifications replacing the...
1966-74 Camaro, Impala, Nova; Starter Solenoid Wire Harness Retainer Clip
Classic $21.99 ea
1961-91 Ford / Mercury; Bendix Starter Drive Assembly; Positive Engagement Type
Replacement bendix drive assembly for Ford 4-1/2" 12V Inertia Starter Motors. Replaces Ford part# C6VY-11350-A or Motorcraft Part# SD-163.
1961-91 Ford / Mercury; Bendix Starter Drive Assembly; Positive Engagement Type
Classic $23.99 ea
1955-56 Chevrolet Starter Ground Strap
Reproduction of the original ground strap used on 1955-56 Chevy models. This strap is used to ground the starter to the chassis.
1955-56 V8 & 6 Cylinder Starter Rebuild Kit
This rebuild kit includes all components needed to bring your starter back to full working order.
1957-72 V8 & 6 Cylinder Starter Rebuild Kit
This rebuild kit includes all components needed to bring your starter back to full working order.
1955-56 Chevrolet Starter Solenoid Plunger Rubber Boot
Replace your torn or missing starter solenoid plunger rubber boot with this fine reproduction. Don't let dirt and grime lock up your plunger!
1954-64 Ford/Mercury; V8/L6; Various Models; Rubber Starter To Flywheel Housing Seal
Reproduction starter to bell housing seal for various 1954-64 Ford and Mercury models with Y-Block V8 and Mileage Maker/Cost Clipper straight-6 engines. Popular applications include Galaxie, Fairlane, Ranchero, and F-Series...
1954-64 Ford/Mercury; V8/L6; Various Models; Rubber Starter To Flywheel Housing Seal
Classic $11.99 ea
1964-80 Ford / Mercury; Bendix Starter Drive Assembly
Replacement bendix drive assembly for Ford 4" 12V Positive Engagement Starter Motors. Replaces Ford part# C4DZ-11350-B.
1967-74 Firebird, Trans Am; Starter Reinforcement Bracket
Reproduction of the original starter brace designed for use with 1967-74 Pontiac models with 326, 389, 350ci engines and 1967-70 400 and 455ci V8 engines, (1970 first design). Each brace is manufactured in stamped steel...
Reproduction starter splash shield or heat shield for various 1966-70 Dodge and Plymouth B-Body models. Many times missing and almost always rusted and in need of repair. This shield attaches to the LH front frame rail on...
1963-82 Chevrolet Corvette; Starter Motor Brace Nut
Starter Motor Brace Nut for 1963-1982 Chevrolet Corvette. From restoration to performance, we are proud to offer the highest quality parts for both classic and late models Corvettes.
2010-15 Camaro With Automatic Transmission (Mx0) - Remote Starter System
This Remote Start Kit seamlessly integrates into Camaro's Anti-Theft and Remote Keyless Entry systems. It is the same Remote Start system that comes from the factory. Important: The Remote Start Kit is only avail able for...
2010-15 Camaro With Automatic Transmission (Mx0) - Remote Starter System
Classic $275.99 set
1956-62 Chevrolet Corvette; Starter Bolts; 3 Piece Set
Starter Bolts 3 Piece Set for 1956-1962 Chevrolet Corvette. From restoration to performance, we are proud to offer the highest quality parts for both classic and late models Corvettes.